Search:

Well as expected the buyer is not that interested in the deal. Once shipping costs come in he is reluctant to have it shipped.

I informed him that I will be placing the Power-Lok on ebay and...

Hi everyone... I finally got the whole thing out today and soon will ship it out.

Just want to give some information on the Spicer locker carrier. I looked at the date code it was made 07/28/70...

Well it looks like some body is getting a good deal, I sold the axle with the Spicer left inside so it is ready for axles and installation. Though not very many now need these as most have upgraded...

Hi

If your interested, I will sell it. At this time I have been asked by another guy, and am waiting on a responce. Though at the time I just had questions and was finding out things about this...

Hi

As I suspected, I verified today that my rear end is a Twin Grip. I though it was strange, when I parked and stored my Javelin, that I could not rotate the rear wheel when the opposite side was...

Hi, I removed my 71's a few years ago and sold it... It should not be too difficult for you since the car had the A/C removed. The only trouble is the hose clamps, and removing the dash pad and...

Hi, I am not sure about your build date, but you are right that the clear ones are for the early 72 Javelin/AMX. What you want to look up is the body number... I am sure someone knows what body...

Edelbrock has heads and intakes... Pistons can be purchased through ROSS or any piston manufacturer. You gan get just about anything you need to rebuild. Mopar B block engines have the same lifter...

I have a 71, and noticed that it has provisions for 3 door hinges. I assume another bottom door hinge will fit in the empty location. As for internals they are the same.

Hi, if you are to use a Ford 9 inch rear end you will need to have the purches moved to fit. Yes, some have claimed to have bolted on a mustang rear, but it works if you have worn out eye-bushings....

Ok, I am done! I went a head and forged through cutting the heads off with my chissel. Just thought that the heads would pop off easier than they did.

Note: Wack away like there is no tomorrow,...

The only thing I notice about it is that depending on the wax you use or not, it will lift it causing you to rewax again ( I guess that would be normal according to what this stuff removes).

Sorry...

Ok, this is going to sound corny, but I am having a tough time cutting the ball joint rivets so I can replace them.

I remember cutting them with a chissel in the past, but the chissel I have seems...

Hi,

A blow dryer will not help on old gum stickem... I just went a head an was able to pop off the old thing with my fingers because it was pitted out and the body was going to the body shop. The...

Thanks for all your input.

Since the driver seat was reappolstered some time ago and I threw away the original carpet after stripping the interier, I think there is no way if any to find it now.
...

Since I was lucky to purchase from the original owner... I have been striping the car down for body and paint. I have yet to come across it. I have found a few interesting lables and tags but no...

I have two bottles one is the original untouched one that came with the car. I also have a new replacement and has the snap lid that was purchaced from AMC by the original owner. He wanted an...

A number of things may be causing this.


Worn distributor bushings
imporperly installed points
Cracked or fouled distributor cap
Worn rotor
Improper plug gap
Worn out, or gummed up dwell...

You may find a 71 service manual on Ebay... i always have one for the year I own. You can get them for about $25.00. Depending on where you live... Public libraries may have it on CD or in the auto...

Hi,

From what I heard the 390 did not get large numbers cast on the side until 1970... 68 and 69 had no marking or small numbers. If you are not familiar with differentiating large and small...

Seen tilts go on ebay for around $100.00 +, and a complete disk brake setups go around $150.00 +... you may get even more with proportioning valve and master cylindar with power unit and rod. It is...

Note Updated 08/24/06: I did not mention about Holley's Power Valve. If not setup properly with the proper pressure rating... your primaries and or secondaries will be lean. Let say you want to keep...

Hi everyone!

I have been sorting out odds and ends before I throw things away.

Found an interesting cap that at first I had thought it was off of a newer car.

I do know that in 71 there was...

Hi,

I had simular issues with my 73 Jav.

It is a simple fix.

Check the wiring from the alternator and the regulator. There are only a few connections so identifying weak contacts should be...

Hi,

I did not catch your problem... is it cranking?

If so... check your coil. (Had a Ford that did not start when cranked after engine was hot from running).

If not... check the wiring at...